Frame Dropping Issue with ASI585MC in SharpCap – Possible USB Bottleneck?

Anything that doesn't fit into any of the other forums
Post Reply
peafowl
Posts: 1
Joined: Wed Jul 23, 2025 3:47 am
Contact:

Frame Dropping Issue with ASI585MC in SharpCap – Possible USB Bottleneck?

#1

Post by peafowl »

Hi everyone,

I'm encountering a rather puzzling issue while using the ZWO ASI585MC camera with SharpCap (64-bit, v4.1.10203) on Windows 10 Pro. Whenever I try to capture at high frame rates (e.g., 100fps or higher), SharpCap starts dropping frames heavily or stops capturing altogether after a few seconds.

Issue details:
  • This happens when the camera is connected directly via USB 3.0 to my laptop (Lenovo ThinkPad, 11th Gen Core i7, 16GB RAM).
  • I've tried different USB cables, but the issue persists.
  • The camera works flawlessly at high frame rates in ASICap with the same setup, so I don't believe it's a hardware issue.
  • In SharpCap, there's no specific error shown — the capture frame rate just drops drastically to 10–15fps or even 0 fps.
What I suspect:
  • Could SharpCap be struggling to handle the high data bandwidth over USB 3.0?
  • Are there any buffer, cache, or camera settings in SharpCap I should tweak to minimize this issue?
Questions:
  • Has anyone experienced a similar problem with the ASI585MC or other high-frame-rate ZWO cameras?
  • Is there a way to enable verbose logging in SharpCap to trace USB data handling or camera behavior?
  • Would using a powered USB hub or a dedicated ZWO driver make any difference?
I'd appreciate any advice, similar experiences, or guidance on how to debug this further. Thanks in advance!

— peafowl
Gfischer
Posts: 323
Joined: Thu Jun 22, 2023 4:20 pm

Re: Frame Dropping Issue with ASI585MC in SharpCap – Possible USB Bottleneck?

#2

Post by Gfischer »

Are you using a smaller roi? That’s a lot of data! There is a setting in camera settings for usb. It’s a slider reduce all the way down might help
User avatar
admin
Site Admin
Posts: 17580
Joined: Sat Feb 11, 2017 3:52 pm
Location: Vale of the White Horse, UK
Contact:

Re: Frame Dropping Issue with ASI585MC in SharpCap – Possible USB Bottleneck?

#3

Post by admin »

Hi,

the first thing to confirm is whether this happens when just viewing the live video images in SharpCap or if it only happens when you start to capture. If it is only when capturing to disk then we need to start thinking about disk write speeds, checking you have the correct save format (SER), etc. If it happens when just viewing the image then try adjusting the 'Turbo USB' setting down a little (you may need to switch it out of auto mode first). Having the turbo USB too high can cause the sort of symptoms you are seeing where the frames stop arriving.

It's also best to do any testing in a minimal setup - the camera connected straight back to the laptop with a single, unextended, relatively short USB cable. If you can make that setup work reliably then gradually change back to your normal configuration, testing with each change until you find the change that starts to cause problems.

thanks,

Robin
User avatar
Menno555
Posts: 1186
Joined: Mon Apr 20, 2020 2:19 pm
Location: The Netherlands
Contact:

Re: Frame Dropping Issue with ASI585MC in SharpCap – Possible USB Bottleneck?

#4

Post by Menno555 »

I had the same issues when capturing with 120fps. And in my case it was what Robin described: my Sata SSD disk couldn't handle it.
I got an M2 NVMe SSD and the problem was mostly solved. It still would fall behind a bit but way and way less then with the Sata SSD.

Menno
Meade LX200 8" f/10 ACF OTA / Ioptron CEM25EC / Zwo ASI071MC Pro / Zwo ASI482MC
Post Reply