Live Stacking and Pausing to Switch Filters

Anything that doesn't fit into any of the other forums
Post Reply
MarMax
Posts: 192
Joined: Sun Sep 19, 2021 11:43 pm

Live Stacking and Pausing to Switch Filters

#1

Post by MarMax »

I've not yet tried this and was curious if a DSO live stack would work with an OSC camera if you paused it and switched filters and resumed.

I'm thinking of luminance (UC/IR cut) as one filter and narrowband (IDAS-NBZ) as the other filter. I'm not sure if order will matter. The thought is to try a 50/50 live stack with 10 minutes of each.

I don't know if switching a flat in the middle of a live stack is even doable. I've wanted to try this for a while now but I've been out of business with clouds for almost two weeks.
User avatar
admin
Site Admin
Posts: 17573
Joined: Sat Feb 11, 2017 3:52 pm
Location: Vale of the White Horse, UK
Contact:

Re: Live Stacking and Pausing to Switch Filters

#2

Post by admin »

Hi,

I think it would probably work in the sense that you could resume the stack and continue adding frames. Quite how nice looking the results would be is another matter entirely!

You could certainly pause, change filter, change flat, adjust exposure (probably needd to try to keep the individual frame brightness similar) and then resume. Stacking just requires enough stars to be detected and any filters (FWHM, brightness) that you have enabled to be satisfied.

It will be interesting to see the results - probably a good idea to save the raw frames from the camera if you don't already do that so that you can re-stack with different options or different software if the output isn't as good as you'd like.

cheers,

Robin
MarMax
Posts: 192
Joined: Sun Sep 19, 2021 11:43 pm

Re: Live Stacking and Pausing to Switch Filters

#3

Post by MarMax »

Thank you for the reply and information!

I've not tried this yet but will give it a go soon. I'm thinking of the Flaming Star Nebula (IC 405 / Sh 2-229) as the test subject.
MarMax
Posts: 192
Joined: Sun Sep 19, 2021 11:43 pm

Re: Live Stacking and Pausing to Switch Filters

#4

Post by MarMax »

I gave this a try last night and it did not work. I'm not sure why but when I resumed stacking the frames would not stack. The display just showed question marks for each frame.

Image

I'm attaching the log as well. I started stacking using an Antlia ALP-T filter and paused the stack to switch to no filter. During the pause I was able to use the FWHM tool to refocus without the filter. I switched the flat file and set a shorter exposure time. Then I resumed the live stack and the result is shown in the screen shot above.
Attachments
Log_2022-11-17T21_17_49-10004.log
(449.12 KiB) Downloaded 65 times
User avatar
admin
Site Admin
Posts: 17573
Joined: Sat Feb 11, 2017 3:52 pm
Location: Vale of the White Horse, UK
Contact:

Re: Live Stacking and Pausing to Switch Filters

#5

Post by admin »

Hi,

there is no 'smoking gun' in the log to point to what went wrong, but the '???' on the FWHM would tend to indicate that there were problems with star detection after the filter change, either

1) The image became dimmer, so no stars (or very few stars) were detected

or

2) The image became brighter, making all the detected stars saturated. SharpCap will not use saturated stars for FWHM calculations, since they give misleading results

In either case, if you try again, flip to the alignment tab of the live stacking settings and see what the star detection numbers look like before and after the filter change - after the change you may need to adjust sensitivity, exposure or other parameters to get the star detection back into a healthy state.

cheers,

Robin
MarMax
Posts: 192
Joined: Sun Sep 19, 2021 11:43 pm

Re: Live Stacking and Pausing to Switch Filters

#6

Post by MarMax »

Robin,

I'm going to try the pause swap resume (PSR) again now that I have an L-Synergy filter. Here is the old CN topic.

https://www.cloudynights.com/forums/top ... techniques

I'm also going to finally configure and try auto-focus so I'm wondering if I can pause live stacking, switch filters, auto-focus, then resume.

The second filter would be narrowband Ha and I'm thinking to stack about 90% L-Synergy then PSR with 10% Ha.

Mike
User avatar
admin
Site Admin
Posts: 17573
Joined: Sat Feb 11, 2017 3:52 pm
Location: Vale of the White Horse, UK
Contact:

Re: Live Stacking and Pausing to Switch Filters

#7

Post by admin »

Hi Mike,

the thing to do is to make sure that the option to 'Start new stack when re-opening after being closed for 1 minute or more' is turned off in the Live Stacking settings tab. That will at least let you try out this approach. There shouldn't be a problem with the autofocus during the live stack pause, but I think I would save my stack before any of the operations that need to suspend it, just as a precaution in case it all goes horribly wrong!

cheers,

Robin
Post Reply