Page 1 of 1

help with plate solving error

Posted: Thu Jan 08, 2026 12:13 am
by Phoenix
im having issues with plate solving and resync in Sharpcap.

this has just cropped up, no changes to software or hardware was working just fine before.

when i try to do a plate solve and sync, even though im right on the target, im getting an offset error of 3.1 degrees, it will then move the mount off the target.

if i do it again it will find the same amount of error, and move in the same direction by 3.1 degrees.

Something is off, but i cant figure out where.

when doing goto moves, ill also occasionally get a failure with the error Move to RA/Dec Position The mount failed to arrive at the target co-ordinates (off by 3.3°). Expected to arrive at RA=06:27:25.0,Dec=+22:10:20, but mount finished slewing at RA=07:14:01.2,Dec=+23:10:58"


i cant even begin to fathom why its doing this. i have no clue where its going wrong.

any help appreaciated.

Re: help with plate solving error

Posted: Thu Jan 08, 2026 2:37 pm
by admin
Hi,

I think this is all going to come down to the ASCOM driver for your mount and how it is configured... Have you changed anything or updated that recently? What mount/ASCOM driver are you using?

Things to look at in the mount configuration are anything to do with 'sync' commands and also anything related to sky models or pointing models.

By default, SharpCap plate solve works by sending the mount a sync command for the plate solve result co-ordinates, which tells the mount 'this is where you are pointing' - fixing any errors at that point. After that, SharpCap sends a new GOTO to the target co-ordinates which should work nicely because the 'sync' means that GOTOs in the same area should be accurate.

However, some mounts can be configured to interpret the 'sync' as 'add another point to the sky model', which breaks the normal SharpCap plate solve + sync. In this case you can either change the 'after plate solve' behaviour in SharpCap to 'Offset GOTO', or put the 'sync' behaviour in the ASCOM driver back to the default. Note that if you choose the 'Offset GOTO' approach then make sure your SharpCap version is up to date as older versions could go wrong if you did the solve+recenter more than once on the same target. New versions also check more carefully that the mount does what it is supposed to during the 'sync' operation.

Hope this helps, if not, a SharpCap log showing the GOTO and subsequence solve + sync operation would help further investigations.

cheers,

Robin

Re: help with plate solving error

Posted: Thu Jan 08, 2026 11:22 pm
by Phoenix
Nothing changed in my setup, this is why I really hate doing any updates, so same skywatcher drivers, same ascom drivers, same sharpcap version (2 versions behind) Its a consistant offset, so if i command it to go one place it will go to that point + 3.1deg. if i solve it will solve where its looking and add another 3.1 deg.

Even more maddening, last night the problem just went away. no changes no updates.
The only thing i did different was to turn on logging so i could get better log files for this post. and then it went away.

I know it will be back. On the first clear moonless night i get.

Re: help with plate solving error

Posted: Fri Jan 09, 2026 1:35 pm
by admin
Hi,

I absolutely agree with you - problems that go away on their own have a tendency to come back again on their own too :(

You probably don't need any additional logging turned on in SharpCap to have a good chance of working this out if it happens again - the plate solve/resync process logs a fair bit of info about what it is doing and what results it gets even with the basic logging, so just catching a log file after it happens would give a lot of info.

If you are on a version of SharpCap from sometime in the last month or 6 weeks then you should be fine in terms of not needing to update right now - there have been no significant changes in this area for a while.

cheers,

Robin

Re: help with plate solving error

Posted: Sat Jan 10, 2026 12:51 am
by Phoenix
Thanks!, yea ill be back with this subject when it crops up again. I'll hopefully have logs next time.

its a bit older than the last month probbly back in summer 2025. im a bit paranoid about updates, espectially in winter when i cant afford to spend precious weather windows on debugging. was hoping to hold off till spring on the updates.

Re: help with plate solving error

Posted: Sat Jan 10, 2026 2:31 pm
by admin
Hi,

OK, well I think there may have been some relevant updates in SharpCap in the last six months or so, so it may be worth updating (you can always go back - just manually uninstall the newer version and re-install the previous one - your settings will not be wiped or anything by this procedure).

cheers,

Robin