Page 1 of 1

SharpCap 4.0 for my new camera?

Posted: Sat Jul 15, 2023 11:53 pm
by Picheta
Hello, I have a question and it is about installing SharpCap. I have Pro version 3.2 and I want to upgrade to version 4.0 (the new one). Version 3.2 works fine, but I want to update it because I have an Asi 678 MC camera and SharpCap doesn't detect it.
This is not a driver problem since the Asi studio software detects it perfectly; therefore, I deduce that it is about SharpCap.
I have tried to download version 4.0 and it gives me an error. I don't know if this is because I have the previous version 3.2 installed or because my operating system is Windows 7, although according to the SharpCap website it should let you download it. Maybe I should uninstall the version I have 3.2 and download the new 4.0?
Do you know how to solve this problem? Thank you so much!!!

Re: SharpCap 4.0 for my new camera?

Posted: Mon Jul 17, 2023 5:30 pm
by admin
Hi,

if you have a fully up-to-date (windows update) version of Windows 7 then SharpCap 4.0 *should* install. However, I haven't tried it for a while as I no longer have any Windows 7 computers.

Do you get a specific error message when trying to install? Please post a screenshot of any error and I will do my best to assist.

thanks,

Robin

Re: SharpCap 4.0 for my new camera?

Posted: Tue Jul 18, 2023 11:58 pm
by Picheta
Hello again, I have tried to install SharpCap 4.0 and it keeps giving me an error. This time I have made a screenshot of the error message that I can read. I am attaching it and I will appreciate any kind of help. Thank you so much!!!
Well, the message does not allow me to attach the screenshot, I write below the type of error that I am seeing:
Setup Failed
One or more issues caused the setup to fail. Please fix the issues and then retry setup. For more information see the log file.
0x80072efd - unspecified error

Re: SharpCap 4.0 for my new camera?

Posted: Wed Jul 19, 2023 6:33 pm
by admin
Hi,

try downloading and installing the Microsoft .NET Framework 4.8 from this link first

https://dotnet.microsoft.com/en-us/down ... -installer

Then, when that has installed, try installing SharpCap again.

thanks,

Robin

Re: SharpCap 4.0 for my new camera?

Posted: Fri Jul 21, 2023 10:15 pm
by Picheta
Hello Robin, I have followed your instructions and I have been able to install SharpCap 4.0, this version also recognizes my new camera, so everything is perfect; just need to wait for clear skies!!! Thank you very much and I congratulate you for this software!!! A hug!!!

Re: SharpCap 4.0 for my new camera?

Posted: Mon May 12, 2025 11:04 pm
by rahunt
I recently acquired a ZWO ASI678MC camera and when attempting to use it the 4.0 SharpCap software found the camera and made a connection and produced an image. I frequently received an error message indicating the camera was disconnected. When it was connected about every 8 to 10 seconds the image had horizonal strips across it briefly. I returned the camera for a replacement and was surprised that the replacement exhibited the same problems. I tried the ASI suit of software and had no problem. I updated to the latest SharpCap 4.1 something. It seemed to work better but gave me an error message about reconnecting about every 10 seconds. I have used SharpCap for several years with a ZWO 224 camera and was very happy with the results. I am running windows 10. I can probably use the ASI software but much prefer the SharpCap since I am more familiar with it. Any suggestions or recommendations? Has anyone else seen these problems?
Ron Hunt

Re: SharpCap 4.0 for my new camera?

Posted: Tue May 13, 2025 12:53 pm
by admin
Hi Ron,

I think the next steps here would be to make sure that you have

* The very latest ZWO Driver (select the Camera Driver download on this page : https://www.zwoastro.com/software/)

* The very latest SharpCap 4.1 (from our downloads page : https://www.sharpcap.co.uk/sharpcap/downloads

Once you have installed those, reboot and try again to see if that helps. If no help then try these steps...

* Make sure you are using the USB cable that came with the camera - no extensions or hubs between the computer and the camera for this testing

* Try different USB ports on the computer

* Turn the 'Turbo USB' setting for the camera from auto to manual, then turn down the value

Hopefully one of these steps will help resolve the issue.

cheers,

Robin

Re: SharpCap 4.0 for my new camera?

Posted: Tue May 13, 2025 9:36 pm
by rahunt
Thanks!