Page 1 of 1

Cannot set the brightness level to complete sensor analysis with QHY163

Posted: Wed Aug 05, 2020 4:57 am
by jekoors
I initially purchased a QHY163M. I could not find a brightness level that would complete all measurements of the sensor analysis evaluation. A light level that will work for one measurement is then too bright for another measurement. Here is the scenario:
Setup:
• The camera is QHY163M using an iPad app that allows me to set the brightness level from 1 to 100% in 1% increments. I have the iPad draped with a single thickness of a thin white t-shirt between it and the camera.
• I have the latest version of Sharpcap Pro (3.2.6383.0) and the newest version of the QHY drivers. I am using Windows 10.
Scenario:
Upon starting sensor analysis, the initial light level assessment wants me to keep the exposure between .1 and 1 second by changing the brightness level. I adjust the brightness level to be as close to and still under 1 second. If I dim the display too much and the exposure goes over 1 second, the ‘Proceed’ button goes dim, and I cannot continue until I increase the brightness to the point that the exposure is less than 1 second. The closest I have gotten is 991 ms.
Once I am close to 1000 ms, I press the press the ‘Proceed’ button and the e/ADU measurement begins and completes successfully. It then begins the linearity measurements. The exposure is set to .01 ms and begins to decrease until it reaches .001 ms. I then get an error message which states “the exposure time required is shorter than the minimum exposure value. Sensor analysis stopped. Restart with lower light levels.”
I can’t lower the light level because, if I do, the exposure will be over 1000 ms and will be too high when I restart the sensor analysis from the beginning. I have the same issue with light levels that produce initial exposures of 100 ms or 500 ms.
I continued trying the sensor analysis many times over several days and it suddenly started to complete successfully when the initial exposure was between 900 and 1000 ms. I have been able to complete the analysis on several attempts as long as I am within that initial exposure range. The one difference I noticed was that during the linearity measurement, the exposure increased from .01 ms (rather than decrease). So there was no risk of reaching the minimum exposure.
One item to note was that the offset was set to 51 for both the e/ADU and linearity measurements. Also. The sensor analysis has worked flawlessly with ASI290M mini and ASI224C.

I then purchased a QHY163C (color) and tried the sensor analysis. I encountered the same issues as I initially encountered with the monochrome version. I have tried it with initial exposures just over .1s, .5s and just under 1s. I have the same issue with the exposure time decreasing from .01ms until it hits the minimum exposure and I get the error.
The monochrome camera still completes the analysis as long as the initial exposure is just under 1 second.
The issue seems to revolve around the direction of the exposure change when the linearity measure starts. A decrease leads to the error while an increase will complete successfully. I did not make any changes to my process that I am aware of when the monochrome camera started to complete successfully. So I am not sure where to go from here. Any help would be greatly appreciated.
I have attached a log file for the error and a screen shot of the error
John

Re: Cannot set the brightness level to complete sensor analysis with QHY163

Posted: Wed Aug 05, 2020 6:23 pm
by admin
Hi John,

there is definitely something odd going on here because from both your screenshot and the log I can see that the exposure is being set to very small values (less than 1 ms), but the image brightness is still at about 80% of peak brightness. This is causing SharpCap to continually reduce the exposure since it really wants the exposure level to be at about the 65% point before it moves onto the next stage. Understanding why this is happening is going to be the key to solving the problem – if you are starting out with an exposure of about 0.1 to 1s that is not overexposed then the image should be almost like once you get down below 1 ms. We need to understand why it isn't going black…

Thanks, Robin

Re: Cannot set the brightness level to complete sensor analysis with QHY163

Posted: Wed Aug 19, 2020 3:49 pm
by jekoors
I have tried some additional exposure settings with the QHY163C camera. Using an exposure of .36 ms the image is dark and the histogram peak is very close to 0%. At an exposure of .35 ms and below, the image is very bright and the luminance histogram peak is at 75%. I have attached screenshots for each exposure. So when the sensor analysis begins the linearity tests at an exposure of .1 ms, the exposure will be less than .36ms and will be incorrectly seen as too bright and Sharpcap will continue to reduce the exposure in an effort to darken the image.
I have tried these exposures in APT and the image continues to dim until about 1 ms which seems to be the lowest shutter speed. There is no sudden brightening of the image.
I really want to be able to use the sensor analysis and exposure calculator in Sharpcap. Where do we go from here?
Thanks in advance for your help.

John Koors

Re: Cannot set the brightness level to complete sensor analysis with QHY163

Posted: Wed Aug 19, 2020 7:09 pm
by admin
Hi,

I think the best thing for me to do would be to change the code to limit the exposure for that camera so that the minimum exposure cannot be put below 0.36 ms. Obviously values below that are pushing the camera into some sort of malfunction mode which produces the very bright image.

Can you check for me to see if the same problem occurs when the camera is in RAW8 mode? I wouldn't like to end up limiting the minimum exposure there if it happens to work properly in that mode.

Cheers,

Re: Cannot set the brightness level to complete sensor analysis with QHY163

Posted: Thu Aug 20, 2020 9:49 pm
by jekoors
The sensor analysis completed successfully using RAW8. The exposure anomaly still manifested itself where .2 ms was dark (2%) while .1 ms or less was lighter (38%). Let me know if you need anything more.

John Koors

Re: Cannot set the brightness level to complete sensor analysis with QHY163

Posted: Fri Aug 21, 2020 8:21 pm
by admin
Hi, those values are quite similar to the ones that you reported for 16 bit mode, so I'm going to go with a minimum of .36 ms exposure in both modes

Cheers, Robin