Hello i use camera QHY 294 M
With the last ver 3.3.7146 the gain max is only 2055
With the ver 3.2.6457 the gain max was correct 3500
i use windows 10 64 bits and the last DLL SDK from QHY
Gain max 2055 for QHY 294M
Forum rules
If you have a problem or question, please check the FAQ to see if it already has an answer : https://www.sharpcap.co.uk/sharpcap-faqs
Please also read about Troubleshooting USB Issues before posting.
*** Please do not post license keys - please report any problems with licensing to 'admin' by private message ***
Please include the following details in any bug report:
* Version of SharpCap
* Camera and other hardware being user
* Operating system version
* Contents of the SharpCap log after the problem has occurred.
[If SharpCap crashes, please send the bug report when prompted instead of including the log]
If you have a problem or question, please check the FAQ to see if it already has an answer : https://www.sharpcap.co.uk/sharpcap-faqs
Please also read about Troubleshooting USB Issues before posting.
*** Please do not post license keys - please report any problems with licensing to 'admin' by private message ***
Please include the following details in any bug report:
* Version of SharpCap
* Camera and other hardware being user
* Operating system version
* Contents of the SharpCap log after the problem has occurred.
[If SharpCap crashes, please send the bug report when prompted instead of including the log]
- admin
- Site Admin
- Posts: 13319
- Joined: Sat Feb 11, 2017 3:52 pm
- Location: Vale of the White Horse, UK
- Contact:
Re: Gain max 2055 for QHY 294M
Hi,
please can you try the following to see what information SharpCap is getting from the SDK:
SharpCap 3.3, go to the settings and enable additional logging of camera hardware communication in the 'Logging' tab.
Once you have made that change, open the camera. Once it opens, close it again fairly quickly (otherwise the log will be very very large!).
If you then look through the log you should see entries about SharpCap asking the SDK what the gain range is - like the ones below:
On the camera I tested with, the gain range is 0->51.
You can do the same in 3.2, but the controls over the logging are in a different place (bottom of first page of settings) and are less granular. The log is a bit less readable too.
Robin
please can you try the following to see what information SharpCap is getting from the SDK:
SharpCap 3.3, go to the settings and enable additional logging of camera hardware communication in the 'Logging' tab.
Once you have made that change, open the camera. Once it opens, close it again fairly quickly (otherwise the log will be very very large!).
If you then look through the log you should see entries about SharpCap asking the SDK what the gain range is - like the ones below:
Code: Select all
Verbose 17:40:48.296478 #1 Camera : SharpCap.Cameras.QHY.Camera.GetControlMinMaxStep :: Starting GetControlMinMaxStep(CONTROL_GAIN)
Verbose 17:40:48.296478 #1 Camera : SharpCap.Cameras.QHY.Camera.GetControlMinMaxStep :: Completed (returned (0, 51, 1)) GetControlMinMaxStep(CONTROL_GAIN)
You can do the same in 3.2, but the controls over the logging are in a different place (bottom of first page of settings) and are less granular. The log is a bit less readable too.
Robin
Re: Gain max 2055 for QHY 294M
I am sorry le ver 3.3 install another directory and the dll qhy was nov 2020 now i install the dll of qhy 27/12/2020 and the gain max is now 3694 very fine tnx for all software is realy good job .
Best regard christian
Best regard christian
- admin
- Site Admin
- Posts: 13319
- Joined: Sat Feb 11, 2017 3:52 pm
- Location: Vale of the White Horse, UK
- Contact:
Re: Gain max 2055 for QHY 294M
Glad you have it fixed
Robin
Robin