Page 1 of 2
No connexion to the mount
Posted: Wed May 12, 2021 9:13 am
by sonata31
Hello Robin
I try to connect my Avalon M-UNO mount and I have the following message
Yet the mount is not connected to other software
With Stargo software I connect without problem
Louis
Re: No connexion to the mount
Posted: Wed May 12, 2021 9:37 am
by sonata31
The log
Louis
Re: No connexion to the mount
Posted: Wed May 12, 2021 10:19 am
by sonata31
Hello Robin
PHD2 also connects without problem
Louis
Re: No connexion to the mount
Posted: Wed May 12, 2021 1:58 pm
by admin
Hi Louis,
it looks like everything works until SharpCap asks the mount for the focal length of the telescope - the mount doesn't implement that and reports as much (which SharpCap is fine with) but after that everything seems to go wrong.
Can you try SharpCap 4.0.7728, which does not have the focal length request in it - if that works then at least we can be fairly sure that the focal length is something to do with the problem. If you uninstall 7785 manually you should be able to install 7728
thanks,
Robin
Re: No connexion to the mount
Posted: Wed May 12, 2021 2:19 pm
by sonata31
HELLO ROBIN
Same problem with version 4.0.7728
Louis
Re: No connexion to the mount
Posted: Wed May 12, 2021 2:46 pm
by admin
Hi,
does the mount work if you don't try to show the configuration window - ie does it show the correct co-ordinates when selected and connected while a camera is open?
It seems odd that everything is working up to the point of showing the configuration (asking the mount for all its properties) and then the configuration goes POP every time.
cheers,
Robin
PS. Does it help to run SharpCap as administrator? Normally I would not suggest this, but sometimes ASCOM can be picky about this, particularly if other applications that talk to the mount are running as administrator.
Re: No connexion to the mount
Posted: Wed May 12, 2021 3:08 pm
by sonata31
Hello robin
If we click on "Install"
If we click on one of the arrows
ScharCap is run in administrator mode
Louis
Re: No connexion to the mount
Posted: Thu May 13, 2021 1:03 pm
by admin
Hi,
I tried installing the StarGo software myself to see if I could work out anything, but since I do not have an Avalon mount, I can't get past it prompting me to choose the COM Port.
I can't suggest anything that I can be sure will help, but there are some more things that might be worth trying:
1) Try connecting to the mount from SharpCap without having StarGo running first - does that give different results from connecting with StarGo already running?
2) Make sure your ASCOM platform is up to date
3) Try using the 'Device Hub Telescope' - this is an ASCOM tool that will handle talking to the StarGo and SharpCap talks to the Device Hub - putting this into the chain may help make whatever problem you have go away.
Hope one of these ideas helps,
Robin
Re: No connexion to the mount
Posted: Thu May 13, 2021 3:48 pm
by sonata31
Hello robin
I have never used Device Hub
A priori in Device Hub I selected ASCOM.AvalonStarGo.NET.Telescope
In SharCap for the mount I selected Device Hub Telescope
It's OK ?
In any case it works I have no error message, I can start / stop the mount
Louis
Re: No connexion to the mount
Posted: Fri May 14, 2021 12:35 pm
by admin
Hi,
yes, that's how the device hub works, instead of
SharpCap => Stargo ASCOM Driver => Mount
you have
SharpCap => Device Hub => Stargo ASCOM Driver => Mount
If you are also using PHD, Cartes du Ciel or similar then connect them to Device Hub too.
Glad that the device hub seems to help,
cheers,
Robin