How to do a Time Lapse using a ZWO Camera and Sharpcap

A place to post guides, instructions and HOWTO documents on the use of SharpCap and Astrophotography in general
Forum rules
One tutorial per topic please.
Please only post content that you have created in this form.
Tutorials should be either in PDF format as an attachment or written in the first post of the topic. Links to video tutorials you created are also acceptable.
Post Reply
Posts: 8
Joined: Sat Feb 17, 2018 5:09 am

How to do a Time Lapse using a ZWO Camera and Sharpcap

Post by localhost » Thu Aug 16, 2018 6:13 am

This is a 'copypasta' from my website: ... d-sharpcap

Time lapse tutorial put together by Matthew Knight using a ZWO Camera and Sharpcap.
I noticed that I wasn't able to find a guide on how to do a Time Lapse so I managed to figure out how to do it, wanted to share this guide with users who are new to SharpCap.

Video Tutorial:
Watch it on YouTube!

ZWO Camera (Optional but recommended)
Having a ZWO Camera will be easy to use unless you're more advanced with a modded cam. Just make sure your ZWO camera has the ZWO 1/3″ 2.1mm 150 degree lens that ships with the camera.
Make sure you install the ZWO camera drivers or Drivers for your camera.

Laptop is needed to run Sharpcap make sure you have a lot of hard drive space... 500GB or more because you can go from 1 hour that will be 16 GB in file size for just 1 hour of recording...

You will need Sharpcap
You can get Sharpcap for free at:

Start up Sharpcap I assume you have the camera connected to your Laptop by this time.

Once Sharpcap is loaded at the top left you should see a tab that says, ''Cameras'' click that tab look to see if your camera is listed, if you're not using a ZWO camera its possible your camera isn't supported by Sharpcap if your camera is a ZWO camera and not listed possible software issue or drivers not installed...

If your camera is listed pick it you should be able to see the sky if the fisheye lens is in focus you might need to play around with it till the sky comes into focus. If it's already dark out and you don't see the sky on Sharpcap you will need to adjust the Exposure and Gain and play around with the fisheye lens until you see the sky.

If you can see the sky and the stars are nicely focused you can begin recording your time-lapse.

Starting Time lapse:
Click the Start Capture tab at the top left of Sharpcap. (See Picture below)

On the Sharpcap - Configure Capture Window you should see: (Picture below)
(Pictures are low quality to help lower the load time. 'Mainly for my website')

1. Single Frame [x]

2. Unlimited [x]

3. Number of frames[x]

4. Time limit [✔]

We wanna go with #4 which is 'Time limit' You need to set the Hour, Minutes and Seconds for how long you would like to Capture.

Keep in mind the longer you record the more hard drive space you're gonna use up however a 10 minute capture for me was only a 15 second playback so the longer you record the longer the finished playback will be.

Under Capture Sequence of Captures:

Sequence Length; This is how many captures you wanna do say you wanna recored for 6 hours but you wanna Capture 1 hour parts 6 times then you'd set the Time limit to 1 hour and the Sequence Length to 6 Which will break 6 hours into 1 hour Captures or you can just set 6 hours for Time limit and have it be 1 big 6 hour capture.

Interval between Captures, If you're wanting to capture a Meteor shower I'd recommend setting it to 00:00:01 to capture every 1 second.

A 10 minute recording for me I only had 15 seconds of video.

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest