I understand your proposal and that should work. Thanks.
However I am still wondering; my routine calls for a Meridian Flip subroutine when -1deg from the meridian (see attached). My understanding was that the meridian was therefore passed. I am mistaken?
Cheers.
Eric.
Search found 44 matches
- Wed Apr 17, 2024 10:08 pm
- Forum: Bug Reports
- Topic: End of sequence after meridian flip
- Replies: 7
- Views: 1352
- Wed Apr 17, 2024 6:54 pm
- Forum: Bug Reports
- Topic: End of sequence after meridian flip
- Replies: 7
- Views: 1352
Re: End of sequence after meridian flip
Hello My MeridianFlip routine is triggered when the meridian is past of 1°. The routine (picture attached) would first record the current position (Step 1), and then immediately after require the mount to point at that same position. The mount would then detect it has to do a meridian flip (via Asco...
- Wed Apr 17, 2024 7:06 am
- Forum: Bug Reports
- Topic: Sequence not stopping on time
- Replies: 1
- Views: 1136
Sequence not stopping on time
Hi Robin,
My sequence was supposed to stop at 7h30 but it was still running 20 minutes after that time See log attached.
Can you please investigate?
Many thanks.
Eric.
My sequence was supposed to stop at 7h30 but it was still running 20 minutes after that time See log attached.
Can you please investigate?
Many thanks.
Eric.
- Tue Apr 16, 2024 11:20 pm
- Forum: Bug Reports
- Topic: End of sequence after meridian flip
- Replies: 7
- Views: 1352
Re: End of sequence after meridian flip
Hello Robin I experienced it again, commanding a plate solve after a meridian flip as part of my routine. See picture attached, it looks like a Sharpcap pop up menu to me. I think it is linked to "Toolbar/Menu input : SharpCap.ViewModels.Actions.SolveAndResyncAction complete" at the end of...
- Sun Apr 14, 2024 6:31 pm
- Forum: Bug Reports
- Topic: Last used camera settings not restored
- Replies: 4
- Views: 1233
Re: Last used camera settings not restored
There it is!
Cheers,
Eric.
PS: if that can help,that issue is knew to me, it wasn't there 2 months ago went I last operated my hardware
Cheers,
Eric.
PS: if that can help,that issue is knew to me, it wasn't there 2 months ago went I last operated my hardware
- Sun Apr 14, 2024 8:28 am
- Forum: Bug Reports
- Topic: End of sequence after meridian flip
- Replies: 7
- Views: 1352
End of sequence after meridian flip
Hi Robin, My sequence didn't go through last night. The stop (after 1.14am) occured after the meridian flip routine was automatically triggered, a routine that has never failed so far. I got a pop-up that was warning that the flip was not advised and required to make a choice (Yes/No) to perform it ...
- Sun Apr 14, 2024 8:17 am
- Forum: Bug Reports
- Topic: Last used camera settings not restored
- Replies: 4
- Views: 1233
Last used camera settings not restored
Hi Robin, I noticed that the Black Level setting is not restored when I switch on Sharpcap. It keeps setting the value to 7936 while I always use 400. Note that the the "Automatically restore last used camera settings when opening camera" is enabled in SharpcapSettings/General. I am using ...
- Sat Apr 13, 2024 5:57 pm
- Forum: The Sequencer and Sequence Planner
- Topic: PHD2 could not begin guiding, state is LostLock
- Replies: 7
- Views: 1453
Re: PHD2 could not begin guiding, state is LostLock
Thanks again Robin.
Much appreciated.
Cheers,
Eric.
Much appreciated.
Cheers,
Eric.
- Fri Apr 12, 2024 2:22 pm
- Forum: The Sequencer and Sequence Planner
- Topic: PHD2 could not begin guiding, state is LostLock
- Replies: 7
- Views: 1453
Re: PHD2 could not begin guiding, state is LostLock
Dear Robin, Coming back to you regarding this topic. Did you have time to implement the correction you mentionned below? As I resumed my observations yesterday night, I came accross a similar issue that put an end to my automated session almost immediately after a guiding lost message, at around 3.3...
- Thu Apr 04, 2024 4:43 pm
- Forum: The Sequencer and Sequence Planner
- Topic: Meridian Flip from West to East
- Replies: 8
- Views: 767
Re: Meridian Flip from West to East
Thanks robin, that's great news!
I just had someone to trim my tree to the North a week ago! If you don't hear from me during this month, then it will be all good!
Cheers,
Eric.
I just had someone to trim my tree to the North a week ago! If you don't hear from me during this month, then it will be all good!
Cheers,
Eric.