Just for people's info;
There are some posts on this in the Yahoo Gemini 2 group forum. These days I'm just always mindful of checking that the scope is going in the right direction and always ready to hit the "stop" button if needed.
Cheers
Search found 24 matches
- Wed Dec 11, 2019 5:08 am
- Forum: Bug Reports
- Topic: Run Away RA slew
- Replies: 4
- Views: 1778
- Wed Dec 11, 2019 5:02 am
- Forum: Bug Reports
- Topic: Plate Solve Sync'ing but Not Re-Centring G11GT Mount Gemini II
- Replies: 16
- Views: 4645
Re: Plate Solve Sync'ing but Not Re-Centring G11GT Mount Gemini II
To continue a little, FYI I'm slowly ironing out issues but really. Now seems that the Gemini 2 Ascom builds two star alignment models. One for the East (Model "1") and one for the West (Model "0"). Go figure. You would think that it should auto know which side its on but seems I...
- Wed Dec 11, 2019 1:23 am
- Forum: Bug Reports
- Topic: 64 bit SC Crashes
- Replies: 22
- Views: 5862
Re: 64 bit SC Crashes
OK - Thanks
- Tue Dec 10, 2019 7:50 am
- Forum: Bug Reports
- Topic: 64 bit SC Crashes
- Replies: 22
- Views: 5862
Re: 64 bit SC Crashes
Thanks Robin
I'll stick with the non-64bit version for now. Yes its a N4200 - yes its low power, not sure about "old" but no matter.
Cheers Richard
I'll stick with the non-64bit version for now. Yes its a N4200 - yes its low power, not sure about "old" but no matter.
Cheers Richard
- Mon Dec 09, 2019 9:54 am
- Forum: Bug Reports
- Topic: 64 bit SC Crashes
- Replies: 22
- Views: 5862
Re: 64 bit SC Crashes
Thanks. Opened SC. Ran procdump and then went to Focus Assistant, all pretty much froze at that point and here is full screen shot of all messages.
The DMP file itself is some 40Mb.
Cheers
The DMP file itself is some 40Mb.
Cheers
- Mon Dec 09, 2019 2:56 am
- Forum: Bug Reports
- Topic: Plate Solve Sync'ing but Not Re-Centring G11GT Mount Gemini II
- Replies: 16
- Views: 4645
Re: Plate Solve Sync'ing but Not Re-Centring G11GT Mount Gemini II
Hi Robin Setup last night and tried a plate solve from within SC. The good news is that I did manage to get a successful solve and re-centre of Stellarium and the mount. I've got lots of little issues that happen - eg Gemini 2 not saving the solved sync, lost SC later, etc etc but main issue is SC p...
- Sat Dec 07, 2019 5:09 am
- Forum: Bug Reports
- Topic: 64 bit SC Crashes
- Replies: 22
- Views: 5862
Re: 64 bit SC Crashes
BTW FYI - downloaded and installed the latest non-64 bit version of SC. That one seems to work fine.
- Fri Dec 06, 2019 9:42 pm
- Forum: Bug Reports
- Topic: 64 bit SC Crashes
- Replies: 22
- Views: 5862
Re: 64 bit SC Crashes
Hi Robin
Opened SC, ran Procdump. Procdump runs and within a few seconds, before I do anything in SC, SC closed.
Am I missing something. Has a file been written somewhere or ………….. ?
Regards Richard
Opened SC, ran Procdump. Procdump runs and within a few seconds, before I do anything in SC, SC closed.
Am I missing something. Has a file been written somewhere or ………….. ?
Regards Richard
- Fri Dec 06, 2019 9:33 pm
- Forum: Bug Reports
- Topic: 64 bit SC Crashes
- Replies: 22
- Views: 5862
Re: 64 bit SC Crashes
Hi Robin
I ran Procdump and it simply closed SC. I ran it again and it then thought two copies of SC were open.
Will try again.
Cheers
I ran Procdump and it simply closed SC. I ran it again and it then thought two copies of SC were open.
Will try again.
Cheers
- Thu Dec 05, 2019 11:14 pm
- Forum: Bug Reports
- Topic: 64 bit SC Crashes
- Replies: 22
- Views: 5862
Re: 64 bit SC Crashes
I've tried rolling back the two ZWO drivers - camera and Ascom. Tried QHY camera. Same result when I open Focus Assistant. I didn't get to Zoom.